Gunsmithing Service

Clean & Oil

Sight Work

Drill & tap barrel or receiver for sights
Cut dovetail in barrel
Install front sight ramp (sweat-on, screw-on or band type)
Install insert in pistol sight
Build up or construct extra high pistol front sight
Install target rib sight on handgun
Install front or mid-rib bead on shotgun
Plug hole and re-drill for bead
Scope Mounting (includes bore sight, gun drilled and tapped, or not)
Bore sighting
Long forcing cone shotgun (plated or unplated)

Barrel, Action, and Rifle Work

Test fire customer gun
Check Headspace
Make Chamber Cast
Lap Barrel
Install liner in barrel (labor only)
Cut and crown barrel
Chamber and fit barrel to action (labor only)
Install Pre-threaded and chambered barrel (Labor only)
Lap in bolt lugs (only)
Welding on new bolt handle
Forging bolt handle
Install Safeties Dakota, Gentry, Mod 70 type w/shroud, or Mark II/Beuhler type
Chapman Swing safety Lever
Trigger Installation Shilen, Timney, Dayton-Traistor, Double or Single set
Install muzzle brake

Shotgun Work

Long forcing cone Non-Plated bores, per barrel
Plated bores, per barrel, or Resolder Rib (only)
Raise dent in barrel
Polish chamber and bore
Back-boring per barrel, non-plated bore
Open/Modify choke or screw-in choke tube
Install Screw-in Chokes (labor only)
Install adjustable choke multichoke, polychoke, etc.
Install Poly-Choke Rib
Make new hinge pin

Handgun Work

Chamfer revolver barrel
Chamfer revolver cylinder
Revolver action job
Rebarrel revolver (labor only)
Straighten crane on revolver
Remove/Modify revolver hammer spur
Semi-Auto action job
Tighten slide of 1911 Auto
Fit barrel to 1911 Non-Ramped, Ramped
Fit and Install barrel bushing on 1911
Bevel Magazine well on 1911
Checker front strap on 1911
Lower and flare ejection port on 1911 slide
Throat, polish barrel & feed ramp of 1911
Fit new trigger to 1911 (labor only)
Fit custom hammer to 1911 (labor only)
Modify 1911 frame for beavertail safety
Install auto pistol compensator (labor only)

Revolver Work

Action, Rebarrel, Remove hammer spur, Front sight insert

Trigger Work

Stock Work

Wood Finishing Hunter finish- unfilled oil finish on average stock, or complicated stock
Gunsmith finish--filled, rubbed oil finish on average stock, or complicated stock
Recut checkering (on average)
Glass Bedding barrel and action
Pillar Bed
Install Recoil Pad (labor only)
Install adjustable butt plate (labor only)
Install sling swivels (labor only)
Install recoil reducer (simple installation in buttstock)
Inletting and finishing semi-inletted stock (only)
Install barreled action in synthetic stock
Recoil pad fitted to length
Shorten length of stock
Bedding (hunter grade - bed recoil lug area and float barrel, entire receiver area float barrel, pillar bedding, float barrel)
Refinish stock - hand rubbed
Sling swivel installation (bolt or other action)
Check headspace
Check firing pin protrusion
Chamber cast
Remove stuck case
Remove live round
Line .22 barrel
Install prethreaded barrel
Chamber, thread, fit barrel
Cut and crown rifle barrel (most)
Lap bolt
Make flat spring
Make U spring

1911 Work

Series 70 or 80 (4# no creep or competition)
Install trigger only
Fit match barrel (and comp, ramped barrels)
Fit extended thumb safety
Fit grip safety
Install stake on sights
Cut dovetail for front sight
Machine for low mount Bo-Mar or Novaks (front and rear)
Checker front strap
Checker trigger guard
Correct loose breech
Bevel magazine well
Reliability package

Metal Finishing

Hot blue
Matte (bead blast)
Deluxe (polished to 400 grit)
Master (polished to 555Grit)
IM Belgian bluing
Slow rust bluing
Teflon

If any work is required that is not listed write, e-mail, or call for a quote.

Shipping costs are the responsibility of the customer.

Circle S Ranch Gunworks

Circle S Ranch Gunworks
Buy-Sell-Trade-Pawn
Larry Smith
3682- 189^th Street
I-70, EXIT 189, South 4.5 Miles
Russell, Kansas
785-483-1124
Mon, Wed, Fri: 5 PM - 8 PM
Sat: 10 AM - 6 PM
circles@russellks.net